Firmware download

UltraView - ServeView Plus - ServeView enhanced

Product Part number Platform Rev Date
UltraView
ServeView Plus
UPc-nU
SPc-nU 
PC U64P 09/13/01
UltraView
ServeView Plus
USc-nU
SSc-nU 
Sun U60S 08/30/99
UltraView
ServeView Plus
UAc-nU
SAc-nU
Apple U60A 08/30/99
UltraView
ServeView Plus
UEc-nU
SEc-nU
Multi U64E 09/13/01
ServeView enhanced
Revision A units
SVE-nU A Multi U62D 09/13/01
ServeView enhanced original units SVE-nU Multi SVE62 09/13/01


NOTES
1. c in part number is chassis style, n in part number is number of ports
2. When upgrading the SVE units, please be sure to distinguish between
the original units and the newer units with an A in the part number.


Program revision history

Program version 62  09/13/2001

Improve mouse performance

Improve compatibility with mouse on various platforms. Mouse would go out of sync on various platforms such as HP LDpro and LXpro. This has been resolved. This does not apply to firmware for Apple and Sun units and no new firmware has been generated in this release for these units.

Program version 60  08/30/1999

Fix upper boards not recognized

Fix problem with upper boards sometimes not being recognized at power up. Randomly, certain units would not recognize the upper boards and you could not switch to these ports.

Fix selection of ports sometimes skipped on upper cards

When switching to a computer on an upper card, sometimes the switching would not occur. Switching to the computer again would work correctly.

Fix box to box mouse problems.

The box to box protocol would sometimes not be configured correctly and the mouse would be out of sync. Careful manual configuration would be able to correct the problem. The box is now easier to configure and forgiving of wrong configuration. If a wheel mouse is not used the box does not use any wheel mouse protocol.

Add set mode command

These commands are present in versions of the switches with no OSD installed.
It has been added in to versions with OSD to make configuration easier.
In particular please note the new settings to configure multi-platform boxes
to all Sun or all Apple. 

Note there are three classes of mode command, for the CPU, for the keyboard, and for the mouse. Don't confuse the setting for a CPU's keyboard/mouse setting with the mouse itself. To change a CPU's keyboard/mouse setting you must first switch to that CPU. Changing the keyboard or mouse itself, you can be switched to any CPU. 

Settings that apply to Apple and Sun are ignored on PC-only units. The mode command is inactive if a configuration password has been set. To enter the mode command, press and release the left control key, then the M key, then the mode value as shown below, and then the enter key. Don't use the numeric keypad for numeric keys or the enter key.

To save the setting in non-volatile memory, use the keep command by pressing and releasing the left control key and then the K key.

 
SUMMARY OF MODE COMMAND VALUES
MODE COMMAND VALUE DESCRIPTION
1 CPU keyboard = PC mode 1 (certain IBM computers)
2 CPU keyboard = PC mode 2 (most PCs)
3 CPU keyboard = Most Unix workstations
4 CPU keyboard/mouse = Apple
5 CPU keyboard/mouse = Sun
6 CPU mouse = PS/2 mouse
7 CPU mouse = RS232 7 bit mouse (Microsoft)
8 CPU mouse = reserved for future use
9 CPU mouse = RS232 Mouse systems mouse
10 CPU mouse = PS/2 wheel mouse
20 Keyboard = 101/102 PC keyboard
21 Keyboard = 104/105 PC keyboard (Windows KB)
30 Mouse = PS/2 mouse
31 Mouse = RS232 7 bit mouse (Microsoft)
32 Mouse = RS232 Mouse systems mouse
40 Set all computers to Apple
50 Set all computer to Sun
60 Set all computers to PC mode 2 and PS2-mouse

Add set resolution command 

This allows you to set the on-screen display resolution when no video is present. This was added primarily to support older fixed frequency monitors that do not sync up at the default 640 x 480 @ 60Hz rate of the on-screen display.

To enter the resolution command, press and release the left control key, then the Y key,  then the resolution value as shown below, and then the enter key. Please note that for German language keyboards you must use the z key instead of the y key.

Don't use the numeric keypad for numeric keys or the enter key. To save the setting in non-volatile memory, use the keep command by pressing and releasing the left control key and then the K key.

 
SUMMARY OF RESOLUTION COMMAND VALUES
COMMAND VALUE RESOLUTION SETTING
1 640x480 60Hz
2 640x480 72Hz
3 640x480 75Hz
4 640x480 67Hz
5 832x624 75Hz
6 1152x900 66Hz
7 1152x900 76Hz

Improve support for Windows NT service pack 3 and 4

We have revised the mouse driver in the box to be compatible with the latest changes. Normally booting of the computer configures the setting automatically, but if a computer is changed to another port or has manually been configured wrong you can lose the mouse. To recover the mouse a new command has been added to send a reset mouse command to the computer.

To enter the reset computer's mouse command, press and release the left control key, then the O (alphabetic, not zero) key. This command should only be used when the mouse has been lost on NT. If a wheel mouse is used, this will also recover use of the wheel. You can also use this command to change the NT mouse driver from non-wheel to wheel without booting the computer.

Fixed problem with mouse on certain Dell computers

Certain Dell computers such as the XPS R350 and the XPS 450 would fail to have mouse pointers present when booting NT4.0. The mouse will now boot properly on these computers.


s 1996-2001 All Rights Reserved